PROLED HR 1270

PROLED HR 1270

The newest and most revolutionary solution for hair removal.

The world's first hair removal equipment with high power LED technology.

HOW IS HAIR REMOVAL ACHIEVED BY LED?

Using high power LED super emitters as a light source, with a continuous wavelength of 780 to 850 nm, close to NIR, which act subcutaneously on the melanin present in the hair follicle until hair removal is obtained.

TECHNICAL ADVANTAGES

USEFUL LIFE AND GREAT STABILITY
Up to 100 million shots and 5 years of useful life with less than 20% loss of power, without using any type of consumable.
Continued stable results, low maintenance cost for the user and the high reliability of the equipment ensure high profitability in its use.
The lifespan of an LED light source is much longer than that of a diode laser.

OPTIMUM WAVE LENGTH AND EMISSION SPECTRUM
PROLED technology emits near-infrared NIR light with wavelength of 780~850nm continuously, mostly absorbed by melanin present in hair follicle, so hair removal is very effective. The light spectrum is broad, so it can be applied on various skin tones, including dark skin.

EXCELLENT EMISSION SURFACE
The 3.74 cm2 (17x22 mm) rectangular spot with uniform emission of energy does not produce any sensation of pain during treatment. The emission of LED light does not cause damage to the eyes as it occurs in diode lasers.
The uniform emission area and the minimum angle of divergence allow it to penetrate easily into the skin to a great depth, so that the deepest hair follicles can be treated as well.
Great penetration of the LED chip due to its high energy and its minimum light divergence angle of only 15 degrees.

TOTAL SAFETY FOR OPERATOR AND CUSTOMER:
PROLED HR 1270 is strictly tested at the factory before shipment and is originally equipped with security software that limits its enormous firing potential to 374 J/sec to avoid any possible damage or accident that could be caused by misuse by the operator.

ROBUST AND EASY TO USE HANDLE
The handle can be changed as a whole and is highly resistant to knocks and falls. During operation, the intelligent LCD screen integrated in it shows the energy used, the pulse interval, the frequency and the number of shots, which is very comfortable for the equipment operator.

HIGH POTENCY: EXCELLENT CLINICAL RESULTS
Total peak power of 2,000 w by means of 12 LED chips produced in the USA, integrated into the handpiece. The type of LED chip makes it easy to place them compactly, thus obtaining a higher power density. Compared to a traditional VCSL laser, the power density is approx. 70% higher, which considerably improves clinical results.

SAPPHIRE CONTACT TEC COOLING
Complete cooling equipment that combines cooling by water and by contact TEC with sapphire crystal that guarantees operating temperatures down to -15ºC, cold enough to protect the epidermis and achieve a very pleasant sensation during treatment.

SMART SOFTWARE
Security software that limits the enormous potential of the equipment to avoid any possible damage or accident that could occur due to its misuse by the operator.

Four treatment modes: Sweep, Interval, Classic and Custom.

Advanced configuration: Allows you to keep an exhaustive control of the use of the machine.

Energy Calibration Function: Energy can be precisely calibrated at any level for effective treatment.

LARGE SIZE SPOT
Large 3.74 cm2 (17x22 mm) spot, very effective for hair removal on large surfaces.

WIFI CONNECTION (Optional)
It allows remote control of machine parameters and facilitates after-sales service.

PRODER HR 1270 PARAMETERS

Light source: high power LED
Emission spectrum: 780~850nm continuous emission
led power: 840w
LED power peak: 2,000w
Pulse Width: 5-750ms
Safety energy: 374 J/sec
Energy density: 1-100J/cm2
Frequency: 1-10Hz

Skin types: I-VI
Operating mode: Sweep, Interval, Classic and Custom
LCD screen: 10”
Spot size: 3.74 cm2 (17x22mm)
Refrigeration temperature: Up to -15 ºC
TEC cooling system by sapphire / water contact
Size: 43x50x87cm
Net weight: 35kg